Harmony Homes INC

Get your Home in Perfect Harmony

Tag: garage door repair Haslet TX

How To Replace Rollers On Garage Door – Haslet Gates & Garage Doors

By

On September 19, 2023

In GARAGE DOOR SUPPLIER

Garage Door Repair Haslet TX are a crucial component of your garage door system. Over time, they can wear out and become noisy or even malfunction, causing inconvenience and potential safety hazards.

Replacing garage door rollers is a manageable DIY project that can save you money on repair costs and improve the overall performance of your garage door. In this guide, we will provide step-by-step instructions on how to replace the rollers on a standard residential garage door.

Tools and Materials You’ll Need:

  1. New garage door rollers (nylon or steel)
  2. A ladder
  3. A socket wrench set
  4. A pair of pliers
  5. A flat-head screwdriver
  6. Safety glasses
  7. A clamp or vice grips
  8. Lubricating spray
  9. Safety gloves

: Safety First

Before you begin, ensure your safety. Wear safety glasses to protect your eyes from any debris or dust that may fall during the process. You should also wear safety gloves to safeguard your hands while working on the garage door.

: Disconnect the Opener

To prevent any accidents, disconnect the garage door opener by pulling the release cord. This will disengage the door from the opener, allowing you to operate it manually.

: Open the Door

Raise the garage door to its highest position using the manual release handle. This will give you easy access to the rollers.

: Secure the Door

To prevent the garage door from accidentally falling, clamp or use vice grips on the tracks just below the rollers you are replacing. This ensures that the door remains in place throughout the process.

: Remove the Old Rollers

Using a socket wrench, carefully loosen the nuts securing the roller brackets to the door. Once the nuts are removed, use a flat-head screwdriver to gently pry the brackets apart, releasing the old rollers.

: Replace with New Rollers

Slide the new rollers into the brackets. Make sure they are positioned correctly and that the stem of the roller fits into the track. Tighten the nuts on the brackets to secure the new rollers in place.

: Lubricate the Rollers

Apply a generous amount of lubricating spray to the new rollers. This will ensure smooth and quiet operation. Roll the door up and down a few times to distribute the lubricant evenly.

: Test the Door

Release the clamps or vice grips and manually open and close the garage door to ensure the new rollers are functioning correctly. If there are any issues, recheck the installation and make necessary adjustments.

: Reconnect the Opener

Once you are satisfied with the roller replacement and the door’s operation, reconnect the garage door opener by pulling the release cord back into position.

: Clean Up

Dispose of the old rollers properly and clean up any debris or tools in your work area. Store any remaining lubricating spray for future maintenance.

Conclusion:

Replacing Garage Door Repair Haslet TX is a manageable DIY project that can improve the performance and longevity of your garage door. By following these step-by-step instructions and taking the necessary safety precautions, you can successfully replace your garage door rollers and enjoy a quieter and smoother-operating garage door. Regular maintenance, including lubrication, will help extend the lifespan of your new rollers and ensure the continued reliability of your garage door.

Haslet Gates & Garage Doors

817-482-3394

How Hard Is It To Replace A Garage Door Opener – Haslet Gates & Garage Doors

By

On August 24, 2023

In Garage Door

Replacing a Haslet Gates & Garage Doors opener is a moderately complex task that involves electrical wiring, mechanical adjustments, and careful installation. While it’s not extremely difficult, it does require some technical skills and a systematic approach. If you’re comfortable with DIY projects and have some basic tools, you may be able to replace a garage door opener yourself.

Here’s a comprehensive guide on the process and what to expect:

Materials You’ll Need:

  • New garage door opener
  • Mounting hardware
  • Wrenches and screwdrivers
  • Stepladder or ladder
  • Power drill and bits
  • Safety goggles and gloves
  • Wire stripper/cutter (if needed)
  • Circuit tester
  • Ceiling joist locator (if needed)
  • Garage door opener manual

Step-by-Step Guide:

1. Choose the Right Opener:

  • Before purchasing a new garage door opener, ensure that it’s compatible with your garage door type, weight, and size. Consider features such as horsepower, drive type (chain, belt, screw), and smart technology options.

2. Gather Tools and Equipment:

  • Collect all the necessary tools and equipment you’ll need for the installation. Read the garage door opener manual thoroughly before you begin.

3. Disconnect Power:

  • Turn off the power to the garage door opener system. This ensures your safety while working on electrical components.

4. Remove the Old Opener:

  • Follow these steps to remove the old garage door opener: a. Disconnect the opener from the door by releasing the emergency release mechanism.
    b. Disconnect all wires from the old opener, carefully labeling them for reconnection.
    c. Remove the old opener’s mounting hardware from the ceiling.

5. Prepare the Area:

  • Clean and clear the area around the opener installation spot. Ensure that the ceiling is free of obstructions and suitable for the new opener’s installation.

6. Install the Mounting Bracket:

  • Follow the manufacturer’s instructions to install the new garage door opener’s mounting bracket on the ceiling. Make sure it’s securely fastened to a ceiling joist.

7. Install the Rail:

  • Attach the opener’s rail to the mounting bracket, following the provided instructions. Assemble the rail sections if needed.

8. Attach the Motor Unit:

  • Mount the garage door opener’s motor unit to the ceiling bracket and secure it using the provided hardware. Make sure it’s level and centered over the garage door.

9. Install the Trolley and Drive Mechanism:

  • Attach the trolley to the rail and secure it properly. Attach the drive mechanism (chain, belt, or screw) as instructed in the manual.

10. Wire Connection:

  • Connect the wires from the opener to the appropriate terminals, following the wiring diagram in the manual. This includes connecting the power supply and safety sensors.

11. Adjustments and Settings:

  • Set the opener’s travel limits, force settings, and any other necessary adjustments according to the manual.

12. Test the Opener:

  • Test the garage door opener by opening and closing the door several times. Make sure the door operates smoothly and stops when it should.

13. Reconnect Emergency Release:

  • Reconnect the emergency release mechanism so you can manually operate the door if needed.

14. Secure Wiring:

  • Secure and route the wiring neatly along the rail and ceiling to prevent tangling or interference.

15. Power On:

  • Turn on the power to the garage door opener system.

16. Test Safety Features:

  • Test the safety features of the opener, such as the auto-reverse mechanism and the safety sensors, to ensure they are functioning properly.

17. Program Remote Controls:

  • Program any remote controls or wireless keypads that come with the new opener, following the instructions in the manual.

18. Troubleshoot (if needed):

  • If you encounter any issues or the door isn’t functioning as expected, refer to the troubleshooting section of the manual or seek professional help.

Conclusion:

Replacing a Haslet Gates & Garage Doors opener requires attention to detail, careful wiring, and the use of appropriate tools. While it’s not the most straightforward DIY project, it’s certainly manageable if you’re comfortable with home improvement tasks. If you’re uncertain about any step or aspect of the installation, or if you encounter unexpected challenges, consider seeking assistance from a professional garage door technician to ensure a smooth and successful installation.

Haslet Gates & Garage Doors

817-242-5042

How to Clean Aluminum Garage Door-Haslet Best Garage & Overhead Door

By

On May 10, 2023

In GARAGE DOOR SUPPLIER

Cleaning an aluminum Garage Door Repair Haslet TX is important to maintain its appearance and extend its lifespan. Aluminum is a durable material that is resistant to rust and corrosion, but it still needs regular cleaning to remove dirt, grime, and other contaminants that can accumulate on its surface.

In this article, we will discuss the steps involved in cleaning an aluminum garage door.

Step 1: Gather the necessary tools and materials

Before you begin cleaning your aluminum garage door, you will need to gather the necessary tools and materials. Here is a list of what you will need:

  • A bucket of warm water
  • A mild detergent or soap
  • A soft-bristled brush or sponge
  • A hose or pressure washer
  • A ladder
  • A microfiber cloth or chamois
  • Aluminum cleaner (optional)

Step 2: Remove any loose dirt and debris

The first step in cleaning your aluminum garage door is to remove any loose dirt and debris. You can do this by using a soft-bristled brush or sponge to gently scrub the surface of the door. Be sure to pay attention to the corners and crevices where dirt and debris can accumulate.

Step 3: Apply the cleaning solution

After removing any loose dirt and debris, you can apply the cleaning solution. You can use a mild detergent or soap mixed with warm water to create a cleaning solution. If you prefer, you can use an aluminum cleaner that is specifically designed for cleaning aluminum garage doors. Be sure to follow the instructions on the cleaner carefully.

Step 4: Scrub the door with a brush or sponge

Once you have applied the cleaning solution, you can use a soft-bristled brush or sponge to scrub the door. Be sure to work in sections and rinse the brush or sponge frequently. You should also pay attention to any areas of the door that are particularly dirty or stained.

Step 5: Rinse the door with a hose or pressure washer

After scrubbing the door, you can rinse it off with a hose or pressure washer. If you are using a pressure washer, be sure to adjust the pressure to the appropriate level for cleaning aluminum. You should also use a wide-angle nozzle to prevent damage to the door.

Step 6: Dry the door with a microfiber cloth or chamois

Once you have rinsed the door, you can dry it off with a microfiber cloth or chamois. Be sure to dry the door thoroughly to prevent water spots from forming. You should also pay attention to any areas of the door that are particularly wet.

Step 7: Inspect the door for any damage

After cleaning your aluminum garage door, you should inspect it for any damage. Look for dents, scratches, or other signs of wear and tear. If you notice any damage, you may need to repair or replace the door.

In conclusion, cleaning an aluminum Garage Door Repair Haslet TX is an important part of maintaining its appearance and extending its lifespan. By following the steps outlined in this article, you can keep your aluminum garage door looking its best for years to come.

Haslet Best Garage & Overhead Door

817-242-5042

How to Put Garage Door Back on Track – Haslet Best Garage & Overhead Door

By

On March 13, 2023

In Garage Door

Putting a Garage Door Repair Haslet TX back on track can seem like a daunting task, but with the right tools and techniques, it can be done easily and safely. Before we begin, it’s important to note that if you’re not comfortable with any aspect of this process, or if you don’t have the necessary tools, it’s best to call in a professional.

Step 1: Clear the area The first step is to clear the area around the garage door. This includes removing any items that may be in the way of the door, such as bikes, lawn mowers, or other tools.

Step 2: Disconnect the garage door opener Next, you’ll need to disconnect the garage door opener from the door. This will prevent the opener from trying to open or close the door while you’re working on it. To do this, locate the release mechanism on the opener and pull it down. You should then be able to manually open and close the door.

Step 3: Inspect the tracks With the door disconnected from the opener, you can now inspect the tracks to see if they’re damaged or misaligned. Look for any bends, kinks, or dents in the tracks, as well as any loose bolts or screws. If you find any issues, you’ll need to address them before attempting to put the door back on track.

Step 4: Align the tracks Assuming the tracks are in good condition, the next step is to align them properly. Start by loosening the bolts or screws that hold the tracks to the garage walls. You don’t need to remove them completely, just loosen them enough that you can move the tracks. Next, use a level to ensure that the tracks are perfectly vertical. If they’re not, you can gently tap them into place with a rubber mallet. Once they’re aligned, tighten the bolts or screws back up.

Step 5: Reinstall the rollers The next step is to reinstall the rollers onto the tracks. Start at the bottom of the door and work your way up, inserting each roller into the track as you go. You may need to remove the hinge that holds the roller in place in order to get it back onto the track. Once all the rollers are in place, test the door to ensure that it moves smoothly up and down the track.

Step 6: Adjust the tension If the door still isn’t moving smoothly up and down the track, you may need to adjust the tension. This is done using the spring system on the garage door. There are two types of garage door springs: torsion springs and extension springs. Torsion springs are located above the door, while extension springs are located above the horizontal tracks. The process for adjusting each type of spring is different, so be sure to consult your garage door manual or call a professional if you’re not sure how to do it yourself.

Step 7: Reconnect the garage door opener Once you’ve got the door back on track and adjusted the tension, you can reconnect the garage door opener. Simply pull the release mechanism back up until it clicks into place. Then, test the opener to ensure that it’s working properly.

In conclusion, putting a Garage Door Repair Haslet TX back on track is a fairly straightforward process, but it does require some knowledge and tools. By following these steps, you should be able to get your garage door back in working order in no time. If you’re not comfortable with any aspect of this process, or if you encounter any issues that you’re not sure how to handle, it’s best to call in a professional.

Haslet Best Garage & Overhead Door

817-242-5042

Powered by WordPress & Theme by Anders Norén